BOB INFANT CAR SEAT ADAPTER Manual do Utilizador descarregar pdf

Congratulations on your purchase of the BOB Infant Car Seat Adapter

(ICSA). It is designed to allow the attachment of an Infant Car Seat

to your BOB Stroller. Please see the table below for the details of

compatible strollers and car seats.

Before attempting to install your new ICSA, read and understand

these instructions completely to insure proper installation.

If you are unclear on any point, contact your dealer or BOB before

use.

WARNINGS

The BOB ICSA is designed for use with single seat BOB Strollers

and recommended Infant Car Seats. Children should not be placed

directly in the BOB Stroller seat with the ICSA installed.

The ICSA Restraint Belt interferes with the proper function of the

safety harness system and the Accessory Tube of the ICSA can

interfere with accessibility. ICSA must be removed from the BOB

Stroller prior to using with a child directly in the seat.

Read and understand stroller owners manual before use.

Read and understand car seat owners manual before use.

Follow assembly instructions. Failure to properly install this accessory

product may result in accidents, severe injury or death. If you are

not sure you can install this accessory, contact your dealer and

arrange for them to perform the installation.

Never leave children unattended in the stroller/car seat.

Always secure the car seat with the restraint belt when the car

seat is placed in the stroller.

Always use seat harness of Infant Car Seat to avoid children from

falling out of stroller.

Refer to your Infant Car Seat owners manual for maximum capacity

limitations.

Always keep your Infant Car Seat handle vertical and locked position

when used in stroller to protect your child.

This product is not a universal adapter. Consult chart for compatibility

with infant car seat brand and model.

Do not strap parcels or bags to the stroller handle or to this product

when installed on your stroller as it affects the balance and stability

of the stroller and can cause it to tip over.

Do not run or jog when using the Infant Car Seat Adapter.

Do not use off-road or on uneven terrain when using the car seat

adapter.

Children develop at different rates. Consult with your pediatrician

regarding the suitability of the stroller use with your child.

BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE

THAT RESULTS FROM OWNERS FAULTY ASSEMBLY OR

MAINTENANCE

AFTER SHIPPING.

Assembly

Instructions

TOOLS NEEDED:

To perform the

installation, you will

need two Philips

Screwdrivers.

Reference Fig. 1 as it

describes the various

parts of the ICSA.

Set parking brake.

Refer to BOB stroller

owners manual for

use and function of

brake.

1. UNPACK: Remove

all packaging material

from product.

Note orientation of

pivot parts and

hardware (Item Nos.

4, 5, & 6). When

installing these parts

they should be

assembled in same

orientation as shown

in Fig. 1.

2. LOCATE THE

ATTACHMENT

POINTS ON

STROLLER: Fig. 2

shows the swingarm

pivot tube locations

where the pivot-plugs

will be installed. Place

the 4 pivot-plugs

(Item 4) inside each

end of both swingarm

pivot tubes of your

BOB stroller as

shown in Fig. 3. In

order to locate and

view the inside

locations, it may be

helpful to push the

fabric seat of stroller

forward and out of the

way.

3. INSTALL THE PIVOT HARDWARE ON STROLLER: With pivot

plugs installed, next install the pivot hardware. Insert one of the female

(long) parts of sex bolt (Item 5) through each pair of pivot plugs (Item

4) from the inside, as shown in Fig. 3, so the threaded ends are just

flush with the outside pivot-plugs.

4. POSITION THE

ICSA ASSEMBLY:

Make sure both the

supports (Item 7) are

rotated forward

before installing ICSA

on stroller as shown

in Fig. 4.

Stretch both ends of

the ICSA main tube

evenly over the pivot

brackets of the

stroller. Be careful not

to pinch your fingers.

One side at a time,

locate each hole at

the end of the main

tube of the ICSA

assembly and line up

with pivot hardware

on stroller.

One side at a time,

push female part of

sex bolt (Item 5)

through ICSA main

tube, and install male

part of sex bolt (Item

6). Tighten pivot

hardware using both

screwdrivers. Tighten

completely (Torque to

10-15 In-lbf).

5. INSTALL UPPER

COMPONENTS:

Move stays of stroller

bonnet (sun canopy)

to a vertical position

as shown in Fig. 2.

Locate and remove

the lower fabric screw

on each side of

handlebar, Fig 2.

Work on one side at

a time, keeping the

other side Support

(Item 7) forward as

shown in Fig. 4.

Rotate Main Tube

(Item 1) back, routing

the Support (Item 7)

between inboard

bonnet stay and

stroller frame until the

hole in the support is

aligned with lower

fabric screw threads

(rivet nut) on

handlebar. Assembly

sequence shown in

Fig. 5. Make sure

restraint belt (Item 9)

is oriented with pull

ring facing out as

shown in Fig. 7. Push

fastener (Item 8) with

pointed end carefully

through support

(Item 7), grommet of

safety restraint belt

(Item 9), then

through fabric

grommet and into

rivet nut on

handlebar. Start

thread by hand.

Using screwdriver,

thread the fastener

straight into the

handlebar. Be

careful: do not cross-

thread. The fastener

is designed to anchor

into the interior

opposite wall of

handlebar.

Hold the restraint belt

in the proper position

perpendicular to

frame as shown in

Fig. 6 and tighten

Fastener (Item 8).

Torque to 10-15 In-lbf

(1-2 N-m). Properly

installed Restraint Belt

shown in Fig. 7.

INSTRUCTIONS

FOR INSTALLING

AND SECURING

YOUR INFANT CAR

SEAT IN BOB ICSA

Your infant car seat

can be placed in and

removed from a BOB

Stroller with the infant

car seat occupied or

vacant. However,

when installing car

seat in the ICSA for

the first time, test fit

with the car seat

unoccupied to ensure

you understand the

process and to make

sure the seat recline

and Accessory Tube

set up is correct for

your type of Infant Car

Seat.

Installation

instructions for the

compatible brands

and models below.

Follow the appropriate

instructions for your

infant car seat.

BRITAX Companion

1. Set parking brake.

Refer to BOB stroller

owners manual for

use and function of

brake.

2. Confirm Accessory

Tube (Item 2) is

installed on ICSA and

secured in place by

two screws (Item 3).

The ICSA is supplied

with the Accessory

Tube installed.

3. Fig. 8 shows the ICSA and stroller in the correct configuration to

accept the Britax Companion.

4. Recline BOB Stroller seat all the way back. Refer to BOB stroller

owners manual for seat-recline feature strap(s) location and function.

5. Rotate BOB stroller canopy all the way back against the handlebar,

Fig. 8.

6. Unbuckle Restraint Belt. Move each belt end outside the stroller

seat so they will not be trapped under the BRITAX, Fig. 8.

7. With car seat handle in vertical (carry) position, gently place the

BRITAX rear facing in the seat of BOB Stroller w/ICSA in a straight

downward motion.

8. Align the bottom channels or grooves of the BRITAX plastic frame

so they rest on the Accessory Tube (Item 2) as shown in Fig. 9.

9. Route restraint belt through slots in car seat and fasten buckle as

shown in Fig. 10.

10. Pull on the ring to tighten the Restraint Belt. When tightened

Lower

Handlebar

Fabric

Screw

Swingarm

Pivot Tube

Bonnet

Stays

Aft Stay

Vertical

Forward Stay

Adjacent

Fig. 2 Attachment Point Locations

BOB Stroller Model Year Compatibility

Model Year(s) Model Serial Number*

2005 and newer Sport Utility Stroller AA000001 and higher

2005 and newer Sport Utility Stroller DLux AB000001 and higher

2005 and newer Ironman AC000001 and higher

2005 and newer Revolution AF000001 and higher

2005 and newer Stroller Strides AG000001 and higher

Car Seat Compatibility

Brand Model Year(s)

Britax

Companion

2003 & newer

Graco

Snug Ride

2003 & newer

Peg Perego

Primo Viaggio

2003 & newer

* Reference Fig. A for serial number location.

Both Car Seat Grooves

Placed on Accessory Tube

Fig. 9 Britax Companion Placed on

ICSA

Restraint Belt

Routed Through

Slots in Car Seat

And Buckled

Fig. 10 Britax Companion Secured With

Restraint Belt

Hold Restraint Belt

Perpendicular to

Handlebar When

Tightening Fastener

Fastener

Fig. 6 Proper Restraint Belt Orientation

Seat Reclined

Accessory

Tube

Restraint

Belt

Outside

Stroller

Canopy Against

Handlebar

Fig. 8 Correct Configuration for Britax

Companion

Pivot

Bracket

Sex Bolt,

Male4 x 8mm

Support

Rotated

Forward

Main

Tube

Fig. 4 Main Tube Aligned for Assembly

Outer

Pivot Plug

Inner

Pivot

Plug

Swingarm

Pivot Tube

Sex Bolt,

Female

Pivot

Bracket

Fig. 3 Pivot Hardware Installation

Buckle and Pull Ring

Oriented To Outside

Fig. 7 Restraint Belt Properly Installed

Serial Number

Located On

Inside of Right

Swingarm

Fig. A Serial Number Location

Fig. 1 Anatomy of the Infant Car Seat Adapter

Main

Tube

Accessory

Tube

Screw

Pivot-Plug

Sex Bolt,

Female

Sex Bolt,

Male

Support

Fastener

Restraint

Belt

Sex Bolt,

Male

Support

Between

Inboard

Bonnet

Stay &

Frame

Fastener

Grommet

Seat Fabric

Restraint Belt

Grommet

Lower

Fabric Screw

Rivet Nut

Fig. 5 Upper Component Installation

MA0516B

Infant Car Seat Adapter instructions

(800) 893-2447 www.bo/jointfilesconvert/426553/bgear.com email- info@bo/jointfilesconvert/426553/bgear.com

Phone: (208) 375-5171 Fax: (208) 375-5172, BOB Trailers, Inc. 5475 Gage St. Boise, ID 83706

1 2 3 4

5475 Gage St. Boise, ID 83706 1

Resumo do Conteúdo

Página 1 - 5475 Gage St. Boise, ID 83706

Congratulations on your purchase of the BOB Infant Car Seat Adapter(ICSA). It is designed to allow the attachment of an Infant Car Seatto your BOB Str

Página 2

Congratulations on your purchase of the BOB Infant Car Seat Adapter(ICSA). It is designed to allow the attachment of an Infant Car Seatto your BOB Str

Página 3

properly, the belt willhold the BRITAXsecurely in place.Make sure the tensionof the belt is notconstricting your child.Before use, verify youhave inst

Página 4

properly, the belt willhold the BRITAXsecurely in place.Make sure the tensionof the belt is notconstricting your child.Before use, verify youhave inst

Mais documentos para Assento para automóveis BOB INFANT CAR SEAT ADAPTER

Para ver o documento BOB INFANT CAR SEAT ADAPTER Manual do Utilizador

BOB INFANT CAR SEAT ADAPTER Manual do Utilizador (12 páginas)

Comentários a estes Manuais

Sem comentários

BOB INFANT CAR SEAT ADAPTER Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Assento para automóveis BOB INFANT CAR SEAT ADAPTER. Infant Car Seat Adapter instructions Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Assento para automóveis BOB INFANT CAR SEAT ADAPTER

Comentários a estes Manuais

Manuais e produtos relacionados com Assento para automóveis BOB INFANT CAR SEAT ADAPTER